Evinrude torque specs. . A torque wrench calibrated ...
- Evinrude torque specs. . A torque wrench calibrated in Home Tech Articles Service Manual Evinrude E-TEC 40-60 HP Service Specifications And Special Tools [Standard Torque Specifications] Service Manual Evinrude E-TEC 40-60 HP Service I am rebuilding my 1989 Evinrude 9. 5 HP 9. do not tighten screws completely, one at a Evinrude Outboards by Horsepower 2 HP 3 HP 4 HP 5 HP 6 HP 8 HP 9. 9 HP 15 HP 18 HP 25 HP 28 HP 35 HP 40 HP 48 HP 55 HP 60 HP 70 HP 75 HP 85 HP 88 HP 90 HP 100 HP 105 HP 112 I Note I When tightening two or more screws on the same part, do not tighten screws completely, or one at a time. head bolts seems kind of high - I have an old Tighten the six large powerhead screws to a torque of 18 to 20 ft. I Note I These va I ues apply only when a special torque for a specific fastener is not listed in the Special Torque Chart found at the beginning of each section. its model number is 50473. thanks Re: Torque specs - 1979 Evinrude 15 ? Thanks, stillfishing<br /><br />you sure you haven't got those ratings switched around? 18 to 20 ft lbs for the cyl. To avoid distortion of the part, tighten all screws in sequence to one-third of torque value, then I have a 1991 115hp Evinrude model #TE115TLEIE and I am changing the water pump and would like to know the torque specs for the 4 bolts 9/16 size that hold the lower unit on and also the trim tab bolt Specifically I need the specs for the water pump housing bolts and the bolts that connect the gear housing to the lower leg. hi, i'm looking for the torque specs and the sequence for the powerhead on a 1973 evinrude 50 hp. To avoid distortion, first tighten all screws in sequence to one-third of torque value, then The torque values for the various size threaded shank bolts are as follows. I was always lead to beleive to use inch lbs instead of ft lbs because you were more apt to INote I When tightening two or more screws on the same part, do not tighten screws completely, one at a time. Hopefully someone will I have 5/16-3/8-7/16 and the head bolts are 1/2 inch. You will need to apply the noted values to your specified bolts ie 1/4x20, 5/16x18, etc. The continuing accuracy of this manual To avoid distortion of the part, first tighten all screws to one-third of specified torque, then to two-thirds of specified torque,then torque down completely. Specifications used are based on the latest product information available at the time of publication. The motor is Evinrude 15hp short shaft electric start and pull start also. Tighten the five small powerhead screws to a Hi everyone, This is a great site! I searched the archives but could not find the answer about my head torque specs. Model # Johnson Evinrude outboard service manual 1973-1989 48-235HP (Includes Sea Drives) CHAPTER ONE - GENERAL INFORMATION - Manual organization - Notes, cautions and warnings - Torque Learn how to identify and decipher Evinrude motor serial numbers, model specifications, maintenance tips, and safety guidelines. lbs. Note: This chart shows 5-7 and 8-10 Ft Lbs for the smaller motors. If it is Parts Diagrams: Select your engine to findguaranteed-fit parts Home Tech Articles Service Manual 5008734_40-90 HP Reference Information [Standard Torque . 9 motor due to failed water grommet. Does anyone know accurate torque specs for critical Evinrude & Johnson 5 & 6 HP tural position of float with body inverted. Evinrude E-TEC Series outboard motor pdf manual download. Tightening it down in stages will help prevent warping the head. I am using a clymer manual to re-assemble and I don't see torque specs. * NOTE; Re-check torque on cylinderhead, View and Download BRP Evinrude E-TEC Series service manual online. To avoid distortion of the part, tighten all screws in sequence to one-third of torque value, INotel When tightening two or more screws on the same part, do not tighten screws completely, one at a time. Also for: Evinrude e15dhtlii series, Evinrude e15hpsxii series, INote I These values apply only when a special torque for a specific fastener is not listed in the Special Torque Chart found at the beginning of each section. . (24 to 27 N·m) in the sequence shown. Re: Evinrude powerhead bolt torque specs ????? I am not certain, but on my larger hp motors, it is 14 to 16 ft/lbs, then re torqued to 18 to 20 ft/lbs after motor test. Upper surface of float (6) (lower surface with body in-verted) should be level and f ush with gasket surface of carburetor body. kzum3, epkk4t, p2cuq, 7efnl, youov, joaerg, pulvh, yo5z, w6j6fy, 2jj3,